Issue link: https://geospatial.trimble.com/en/resources/i/1482398
Contact us: Please do get in touch for further information on any of the products or services mentioned in this case study, a demonstration, support or just a chat about your requirements. T: 0345 603 1214 / IRE: 01 456 4702 E: info@korecgroup.com www.korecgroup.com In order to have line-of-sight to all the planned prisms, the S8 was mounted on a 4m steel column fixed to a concrete block for stability. The instrument would be uncovered to avoid impeding the line-of- sight when tilting. In preparation for the work, a cherry picker was used to enable Vince to attach prisms where required. This included the two faces of the Victorian Chimney and across the Hall itself but only into easily reparable concrete rather than brick work. On the nearby Royal College Of Organists building no intrusive fixings were allowed so the SRM team developed a bracket for attaching onto the ornate grills around the windows. Planning key to monitoring success An additional challenge was that monitoring during the daytime needed to be far more intensive than that at night time. Vince wished to retain the simplicity and cost-effectiveness of a one instrument system and decided that two frequencies of measurement would work best. He was able to set this up in Trimble's T4D software so that during the day, the S8 would take readings from one third of the 'primary point' prisms every five minutes over an eleven month period; during the night, the measurement round would include all prisms but at hourly intervals. Not only did this mean that the site required just one instrument for monitoring, but also that Vince could change the measurement pattern during the day if he was required to provide more detailed information for the stakeholders. This could be done without affecting the night time set up. T4D was also used to set up the alarm tolerances for alerts. For Vince, one of the key aspects of any monitoring project is to develop a good working relationship with all stakeholders and he reports that reliable, accurate and understandable information is vital if this relationship is to succeed. Because Trimble T4D uses a web-based interface, all permitted parties can view the information coming from the system live on a range of convenient devices from computers to mobile phones. This gives an excellent range of 'at a glance' graphical information for the stakeholders and enables them to manipulate and extract exactly what they needed for both their own reporting and in order to ask relevant questions. Additionally, once a week reports are autogenerated with further graphics and data and these reports are emailed to all stakeholders. The quality of the reporting has proved useful to Vince for ensuring that all involved trust the accuracy of the information they are being provided with. So much so that following a request from a concerned party wall surveyor for the installation of tilt beams in a basement, Vince was able to provide the surveyor with sufficient information to reassure him that just a couple of tilt beams would be sufficient rather than an additional full building monitoring system. In previous cases this had not been an accepted proposal, but in this case, the surveyor was sufficiently reassured by the data that Trimble T4D provided. Thoughts for the future The simplicity of the system that Vince installed meant that one SRM site engineer, picked to be the 'eyes and ears' on site, was able to check the system each day and although initially unfamiliar with it, was astounded by its simplicity. Throughout the project, the S8 delivered accurate, reliable data, in all weather conditions without the need for any maintenance. The project has also been a useful learning curve for future monitoring jobs. When work began, the Settop M1 communications hub had not been released. This small, robust blue box is connected to a Trimble Total Station and totally takes care of the communication between the instrument and T4D. It can power cycle the instrument remotely, send measurement data via several communication methods including internal cell phone SIM card, measure air temperature and store measurement data onboard if there are any communication issues, particularly at busy network times during the days. This greatly simplifies the setup and maintenance of a real-time monitoring total station. In future projects, Vince will also look at using an S8 or S9 with Trimble VISION Special brackets were made for mounting the prisms on the Royal College of Organists building The Trimble S8 The Victorian chimney needed careful monitoring technology. The Albert Hall project created a lot of interest and VISION technology would have allowed him to provide images for both the stakeholders and other project engineers in SRM. Finally, the need to incorporate information from other sensors into T4D, in this case, from the tilt beam sensors has resulted in the SRM team automating this process for future projects.